 |
|
10/100 LAN
Provides 10/100 Mbps solution to your network or broadhand connection without having to buy an extra LAN card. |
|
|
|
 |
|
AGP 4X
AGP 4X supports 1 GB/s data rate and runs at 266MHz. |
|
|
|
 |
|
FSB 400MHz
Supports 400MHz front side bus Intel Pentium 4 CPU |
|
|
| |
 |
| CPU | º Socket 478 for Intel Pentium 4 processor
º FSB 400 MHz
| | CHIPSET | º Intel® 845 & ICH2
º North Bridge: Intel® 845
º Intel® 82801BA (ICH2)
| | MEMORY | º 3 x 168-pin SDRAM DIMM socket support up to 1.5 GB
º Support PC133 3.3V SDRAM
Due to the operating system limitation, the actual memory size may be less than 4GB for the reservation for system usage under Windows® 32-bit OS.
For Windows® 64-bit OS with 64-bit CPU, there is no such limitation
| | EXPANSION SLOT | º 1 x AGP 4X slot
º 3 x PCI slots
º 1 x CNR slot
| | STORAGE | º Support by Intel® ICH2
• 4 x Ultra DMA100/66 devices
| | AUDIO | º Realtek ALC201A 2-channel audio CODEC
º Compliant with AC'97 2.2 specification
| | LAN | º Realtek RTL8100 10/100 Mbps Fast Ethernet Controller
| | REAR PANEL I/O | º 1 x PS/2 keyboard & PS/2 mouse connectors
º 2 x USB 1.1 ports
º 1 x RJ45 LAN connector
º 1 x Parallel port (LPT1)
º 2 x Serial ports (COM1 & COM2)
º 1 x Game port
º 1 x Audio port (Line-in, Line-out, Mic-in)
| | INTERNAL I/O CONNECTORS & HEADERS | º 1 x 20-pin ATX Power Supply Connector & 4-pin 12V Connector
º 1 x FDD connector supports one 360K~2.88MB FDD
º 2 x IDE connectors
º 1 x IrDA for SIR header
º 1 x Speaker header
º 1 x USB 1.1 header support additional 2 USB ports
º 1 x Front panel switch/LED header
º 1 x Front panel audio header
º CD in1/CD in2 header
º CPUFAN/PWRFAN/CASFAN connectors
º WOL/WOM connectors
| | SYSTEM BIOS | º Award BIOS with 2Mb Flash ROM
º Supports Plug and Play 1.0A, APM 1.2, Multi Boot, DMI
º Supports ACPI revision 1.0 specification
| | FORM FACTOR & LAYERS | º Micro-ATX Size (244mm*244mm), 4 Layers
|
 Loading... Please wait.
| IMPORTANT NOTE: | | Please read the notes carefully before updating BIOS.
| 1. | Do not update the BIOS if the system is running fine. Unsuccessful BIOS flash may cause the system fails to boot up. The manufacturer is not responsible for any BIOS flash failure.
| | 2. | Make sure your M/B PCB version number first, and then read the updated description & special note carefully to check if the new BIOS version patch pertain to your current problem.
(How to recognize the M/B PCB version)
| | 3. | Please DO NOT reboot system,unplug power supply and remove battery during BIOS update process.
| | 4. | It is recommended to use the updated flash utility included in each BIOS download package.
(How to use flash utility).
|
| | |
Question
Does P4IBMS support "chassis open detect"? I am unable to find the setting on the motherboard. |
Answer
P4IBMS didn`t support "chassis open detect" feature
|
Question
Please show me what problme is solved by 1.13b.I tested the following test cases on Win98 and WinME1. Sis screen saver : 1min / Monitor off : 2min == system cannot resume2. 3D Flower box screen saver : 1:min / Monitor off : 2min == systemcannot resume |
Answer
V1.13C driver fixed also passed logo
|
Question
On the P4IBMS BIOS ver 1.0D with an ATI Xpert 2000 Pro (Rage 128 Pro Ultra chipset) video card installed the system will not successfully recover from a Suspend To Ram. The system suspends fine, then when the power button is pressed to wake the system, the screen fills with garbage and the system reboots. In the BIOS when S1 is selected in place of S3, the system works. The same ATI video card works on ASUS and Giga-Byte boards with the Intel i82845 chipset. The operating systems I have tried are Windows 2000 Pro (Service Pack 2) and Windows XP Pro. |
Question
Could you please let me know what is VID 0 - 4 for? I did not find it fromuser's manual but on the silk screen it says VID0-4 for CPU VOL and short 1-2 isnormal and 2-3 is GND. Could you please explain to me when and how we shoulduse this jumper settings? |
Answer
Actually , the jumer is only for first pliot run testing only , please ask your customer don't to adjust the jumper .
|
Question
what voltages are, for all VID jumper configurations? |
Answer
Please don't care this jumper , it is for facory special testing , it is for factoryspecial tooling/testing .
|
Question
21. Problem Description:The following error message appears at DirectSound test in DirectX Diagnostic Tool.This audio card does not support hardware buffer. Software buffer needs to be used.Is this as designed? |
Answer
It's Intel ICH2 limitation
|
Question
P4IBMS and the P4IBAS boards have similar problem that the SMBIOS is not properlyreporting the number of PCI slots. you can see this through WMI (partof the OS) or through your DMICFG utility. |
Answer
on board with 3 PCI slots + on board LAN = 4 , it is correctly .
|
Question
Using three modules of 1GB registered ECC memory (3x1GB total 3GB), the board keeps restarting under Windows Me. |
Answer
The Intel 845 chipset doesn't support "ECC with register memory" , this is an Intel specification limitation.
|
Question
What is the maximum CPU and HDD capacity supported in P4IBMS v1.0X M/B ? |
Answer
P4IBMS v1.0X ,maximum CPU and HDD supported information as below,
HDD:250G
Pentium 4 400Mhz FSB (256K/512K L2 cache) CPU – 2.4G.
Pentium 4 533Mhz FSB (512K L2 cache) CPU –No support
Pentium 4 800Mhz FSB (512K L2 cache) CPU –No support
Celeron 400Mhz FSB (128K L2 cache) CPU – 1.8G Mhz
Pentium 4 533/800Mhz FSB (1M L2 cache) CPU – No support
Celeron D 400Mhz FSB (256K L2 cache) CPU – No support
|
* means validated by ECS at time of writing. Changes to component or CPU may produce a different outcome. The result shown is for reference only and is subject to change w/o notification.| Socket | Family | Processor | Wattage | Frequency | Cache | Stepping | Since BIOS | | Socket 478 | Intel Pentium 4 | N/A | N/A | 1.7 GHz | 256K | N/A | 1.1d | | Socket 478 | Intel Pentium 4 | N/A | N/A | 1.8 GHz | 256K | N/A | 1.1d | | Socket 478 | Intel Pentium 4 | N/A | N/A | 1.9 GHz | 256K | N/A | 1.1d | | Socket 478 | Intel Pentium 4 | N/A | N/A | 2.0 GHz | 256K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 1.7 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 1.8 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.0 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.1 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.2 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.3 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.4 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.5 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.6 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.7 GHz | 128K | N/A | 1.1d | | Socket 478 | Intel Celeron | N/A | N/A | 2.8 GHz | 128K | N/A | 1.1d |
|
Model:
|
|
P4IBMS
|
|
PCB Version:
|
|
V1.0B
|
|
Expansion_Slot:
|
|
AGP4X
|
|
|
|
|
|
USB:
|
|
1.1
|
|
|
|
Audio Pin:
Front Panel Audio Connector
|
|
|
|
USB Pin:
Front Panel USB Connector
|
|
|
|
IR Pin:
Infrared Port
|
|
|
|
|
|