Please replace that AMD Athlon X2 7850 Black Edition (Kuma) by another working CPU on your GeForce6100PM-M2/V2.0. Then download the latest BIOS (09/03/06) from the following link & update it on the MB. After you get it done, the MB will work with the AMD Athlon X2 7850 Black Edition (Kuma) CPU.Please refer to Product page - Download tag

This model PCB 2.0  with Award BIOS can not support AM3 CPU due to specification. Please check your BIOS is Award BIOS or AMI BIOS supported.  Click here to check.

For motherboard PCB 2.0/2.0A with AMI BIOS, please refer to this link for further support. Please refer to Product page - CPU tag

This error code is related to the Microsoft Universal Audio Architecture (UAA) Bus Driver for High Definition Audio ,Please refer to the steps as below how to fix it .
1.This board comes with Realtek ALC662 6-channel audio ,please download its driver on the following website ,and save it to disk ;
Please refer to Product page - Download tag
2. In "Device Manager", if Microsoft UAA Bus driver is already present in "Systerm devices" , then right-click and select "Disable" ,and then, also try right-clicking and select "Uninstall" to remove it ;
3. Reboot in safe mode ,now install the downloaded Realtek driver .

The warning message means the system will be instable when overclocking. It reminds you to reset a suitable CPU frequency in the CMOS Setup to make the system run stable. There is no guarantee when overclocking because there are factors will influence the outcomes like CPU, RAMs'quality and stability. 

- This is normal. When change to other AMD CPU, the BIOS will prompt,
“Verifying DMI Pool Data, AMD Data Change, Update New Date to DMI!”.

- Once you restart the system, DMI will be updated. The BIOS will prompt,
“Verifying DMI Pool Data, AMD Data Change, Update New Date to DMI! Update Success.”

The BIOS define “DMI” be always updated, so every time you can see,
“Verifying DMI Pool Data, AMD Data Change, Update New Date to DMI! Update Success” when you start the system.

If your board use the Award BIOS, the following link of the CPU Support Table has listed the CPU that ECS had tested and qualified.

http://www.ecs.com.tw/ECSWebSite/Product/Product_Detail.aspx?DetailID=857&CategoryID=1&DetailName=Feature&MenuID=20&LanID=9#fragment-CPU

For motherboard PCB 2.0/2.0A with AMI BIOS, the following link of the CPU Support Table has listed the CPU that ECS had tested and qualified.

http://www.ecs.com.tw/ECSWebSite/Product/Product_Detail.aspx?DetailID=1036&CategoryID=1&MenuID=20&LanID=9#fragment-CPU

*Please enter the BIOS setup menu by “Del” key while start up system or follow manual instruction to get into the setup menu.

- This is the AMI BIOS as the string indicated.


- This is the Award BIOS as string shown in Setup menu.

The BIOS code base for GeForce6100PM-M2 comes with Award or AMI. Then download the corresponding BIOS from below website, and update it.
Award BIOS download URL:
http://download.ecs.com.cn/dlfileecs/bios/mb/k8/GeForce6100PM-M2/61M29306.zip

AMI BIOS download URL:
http://download.ecs.com.cn/dlfileecs/bios/mb/p4/GeForce6100PM-M2/61M2813.zip

*Remind, the BIOS cannot be flashed between Award BIOS and AMI BIOS.
*Please enter the BIOS setup menu by “DEL” key while start up system or follow manual instruction to get into the setup menu.

- This is the AMI BIOS as the string indicated.


- This is the Award BIOS as string shown in Setup menu.

When you insert an external PCI-Express graphics card to motherboard, you don’t need to do anything in BIOS setup menu to disable on-board graphics. The PCI-Express graphics card will be the first priority as output and on-board graphics will be automatically disabled. The external graphics card will be automatically detected by system and works normally.

Please help to checking the following steps first.

1. Check the function of USB ports via another USB device.

2. Check the front panel and back panel both can be used or not while connecting USB devices.

3. Check the USB controller is enabled via BIOS setup menu.  


4. Check USB device driver  well installed or not under device management of operation system. 


5. Check USB device power comsumption. It is 500mA for each ports. If device needs 
     more power to drive, please check the device specfication and provide external to drive the device. 

6. Clear CMOS by taking off the battery and install it back and then check whether system can recognize the
     device or not again.


If all above does not work, you may need contacting for RMA service by your seller.
Thanks!
http://www.ecs.com.tw/ECSWebSite/W2B/WhereToBuy.aspx?MenuID=5&LanID=0&AreaID=5&CountryID=61&TabID=1&ln=1

Please download the drivers from the link below.

http://www.ecs.com.tw/ECSWebSite/Product/Product_Detail.aspx?DetailID=857&CategoryID=1&DetailName=Feature&MenuID=20&LanID=0#Fragment-Download

The model comes with two DDR2 sockets. The memory controller supports DDR2 memory DIMM frequencies of 800/667/533/400. The below memory support table has listed the memory model that ECS had tested and qualified.

If you encounter the CMOS checksum error after powering on the system, please try below suggestions if the symptom is solved.
1. Follow the prompt message to press “Del” or “F1” key enter CMOS setup menu, then Load 
    Optimized Defaults, Save &  Exit Setup.
2. Change a new battery, then enter CMOS setup to Load Optimized Defaults, Save & Exit Setup.
3. Update the latest BIOS. Click here to download it.
4. If all above does not work, you may need contacting for RMA service by your seller.
http://www.ecs.com.tw/ECSWebSite/W2B/WhereToBuy.aspx?MenuID=5&LanID=0&AreaID=5&CountryID=61&TabID=1&ln=1

Before using RAID feature, you need to enable and configure RAID. Please refer to the  RAID manual how to enable RAID feature.

For more information, please refer to,
http://en.wikipedia.org/wiki/Computer_data_storage

• get_app Download Link

No, you can not update BIOS between different PCB verision. Before flashing BIOS, please pay attention to model name and PCB version again. This can prevent the mistake and lead to MB boot failed.

RAID stands for Redundant Array of Independent Disks. It  is a technology that provides increased storage reliability. This model can support RAID0, RAID1, RAID0+1, RAID5 configuration.

For more information, please refer to,
http://en.wikipedia.org/wiki/Computer_data_storage

SPDIF (Sony/Philips Digital Interface) is a digital format, is used for transporting stereo digital audio signals on PC audio cards, CD players, DVD players, and other devices which transmit or receive stereo digital audio. If your motherboard has SPDIF header, you can connect such digital devices to your computer. There are two kinds of SPDIF connections: optical fiber and coaxial cable. Here is SPDIF pin definition for you reference.


If external graphics card support SPDIF in with two pins, please also make sure graphics card's pins definition. Then connect the two cables as following to support this funciton.
1. SPDIF out  from MB Pin#1 to SPDIF in to graphics.
2. Ground (GND) from MB Pin#4 to graphics Ground.  

Please refer to the below photo of PANEL1. Pin1-3 is HDD LED, Pin2-4 is power LED, Pin5-7 is reset switch, Pin6-8 is power switch.